Poster A: Materials
009 India
Effect of Phosphorous Addition on Tribological Behavior of Copper Processed Through Powder Metallurgy
Leevan Rajendran, Vikram Sarabhai Space Centre
042 Taiwan
Thermoelectric Properties of Zn4Sb3 Prepared by Mechanical Alloying and Different Consolidation Routes
Pee-Yew Lee, National Taiwan Ocean University
154 USA
Thermal Fatigue Modeling of Thermal Barrier Coating
Abhilash A. Gulhane, Indiana University—Purdue University Indianapolis
159 USA
Synthesis and Characteristics of Magnesia-Based Metal Oxide Powders by Co-Precipitation Method
Bonggu Kim, Indiana University—Purdue University Indianapolis
213 USA
The Study of Dynamic Recrystallization and Microstructural Analysis on Additively Manufactured 316L Stainless Steel
Hajime Yamanaka, California Polytechnic State University, San Luis Obispo
216 USA
Texture Evolution in Electron Beam Powder Bed Produced Ti-6Al-4V with Varying Build Strategies
Alec I. Saville, Colorado School of Mines
222 USA
Investigation of the Selective Laser Melting Process for AlSi10Mg and AA6061 Fabricated at High Laser Power
Michael V. Pires, Lehigh University
224 USA
Binder Jetting Additive Manufacturing for the Development of Cobal Chrome Biocomposite
John J. Ruprecht, Minnesota State University Mankato
232 USA
Fabrication, Characterization, and Analysis of Functionally Graded Titanium—Titanium Diboride Plates
Nicholas S. Palsgaard, Sacramento State
249 Canada
Binder Jet Printing of a Low-Cost Water-Atomized Tool Steel Powder
Ryan Ley, Dalhousie University
250 Canada
In Situ Nitride Formation in Aluminum Components Produced by Directed Energy Deposition Additive Manufacturing
Maude Tremblay, Laval University
251 Canada
Promoting Chemistry Homogenization in Lean PM Steels Through Utilization of a Master-Alloy
William Bouchard, Laval University
254 USA
Effect of Heat Treatment on SLM 316L Stainless Steel
Andrew Yap, California Polytechnic State University, San Luis Obispo
259 USA
In Situ Gas-Phased Passivation of Low-Pressure Gas-Atomized Calcium Powder
Charles Czahor, Iowa State University
264 USA
Microstructural Features in Additively Manufactured Duplex Stainless Steel Alloys
Andrew D. Iams, The Pennsylvania State University
268 USA
Advanced Corrosion Studies of Laser-Powder Bed Processed 420 Stainless Steel
Alexander J. Gupta, University of Louisville
268 USA
Advanced Corrosion Studies of Laser-Powder Bed Processed 420 Stainless Steel
Alexander J. Gupta, University of Louisville
Poster B: Processing
011 USA
Effect of Hybrid Post-Sinter Treatment on Sinter Hardened Structural Parts from PM Steels
Andrew A. Serafini, The Pennsylvania State University—DuBois Campus
39 USA
Influence of SLM Processing Parameters on Mechanical Properties of Tungsten-Heavy Alloys
Bartlomiej K. Bancewicz, Lehigh University
045 USA
Effect of Scanning Strategies on the Melt Pool Geometry during Powder Bed Fusion Additive Manufacturing
Antonio Magana-Ceballos, California State University Los Angeles
050 Canada
A Novel Method for Determining the Packing Factor of Powder for Electron Beam Powder Bed Fusion Application
Basel Alchikh-Sulaiman, Department of Mining and Materials Engineering, McGill University
128 USA
Electron Based Physical Vapor Deposition Model for Thermal Barrier Coating Fabrication
Anvesh Dhulipalla, Indiana University—Purdue University Indianapolis
155 USA
3D Printing of Biomimetic Inspired Zircon Ceramic Structures
Piyush P. Raikar, Indiana University—Purdue University Indianapolis
208 Canada
Imaging the Interaction of Multiple Water Sprays to Demystify the Atomization Zone During Ferrous Metal Atomization
Ali Asgarian, University of Toronto
210 USA
Process Parameter Development for LPBF of AF9628 Steel
Erin M. Hager, Air Force Institute of Technology
211 USA
Improving Mechanical Properties of LPBF Nickel Alloy 718 by Supersolvus Annealing
David Newell, Air Force Institute of Technology
217 USA
Additive Manufacturing of Aerospace Components
Katrina S. Johnston, Drexel University
219 USA
Combined Experimental and Modeling Study of Copper Nanoparticle Sintering in Intense Pulsed Light Sintering Process
Xuehui Yang, Indiana University—Purdue University Indianapolis
220 USA
Exploration of Powder Processing, Heat Treating, and Texturing Eventual Gas-Atomized Alnico Magnets with Near-Final Shape for use in Electric Drive Motors
Emily A. Rinko, Iowa State University
221 USA
Dislocation and Oxide Dispersoid Density Comparison Between As-Mechanically Alloyed 14YWT Powder and Cold Sprayed then Heat Treated GARS Fe-ODS Powder
Rebecca Whitesell, Iowa State University
225 USA
Marangoni Convection in Selective Laser Melting of 316L Stainless Steel
Prakash Gautam, Montana Technological University
226 USA
ZrC-W Composites Prepared by Reactive Melt Infiltration of Zr2Cu Alloy into Binder Jet Printed WC Preforms
Rina K. Mudanyi, North Carolina A&T State University
227 USA
Parameter Optimization of AlSi10Mg Alloy System in 200W Direct Metal Laser Sintering Process
Matthew White, North Carolina State Univeristy
228 USA
Diffusion Bonding of Silver-Graphite-Copper Composites in Different Atmospheres
Linsea H. Paradis, The Pennsylvania State University—DuBois Campus
231 USA
The Influence of Precursor Derived Secondary Structures on the Sintering Behavior of Binder Jet 3D Printed Titanium Dioxide
Lynnora O. Grant, Rice University
233 USA
Fabrication of Functionally-Graded Stainless Steel 316L Bulk Structures by Selective Laser Melting
Yash Parikh, Texas A&M University
234 USA
Investigation of Compositional and Structural Evolution of Passivation Layers to Absorbed Water on Cold Spray Aluminum Powders
Cameron Crook, University of California, Irvine
235 USA
Spark Plasma Sintering of Aluminum Powders
Olivia Brandt, University of California, Riverside
236 USA
Synthesis of Graphite-Molybdenum Carbide Composite by High-Energy Ball Milling
Madelyn F. Madrigal Camacho, University of California, Riverside
240 USA
Laser-Based Additive Manufacturing of High-Performance High-Entropy Alloys
Jie Ren, University of Massachusetts Amherst
241 USA
Effect of Powder Reuse on Static Mechanical Properties of Stainless Steels Produced Through Selective Laser Melting
Jessica H. Schiltz, University of Notre Dame
244 USA
Mechanical Testing and Characterization of Hot Isostatic Pressed and Heat Treated Additive Manufactured Inconel 718
Jaime Varela, University of Texas at El Paso
247 USA
Processing, Characterization and Bio-Tribocorrosion of Silicon and Calcium Phosphate Reinforced Ti6Al4V for Load-Bearing Implants
Jose Avila, Washington State University
248 Canada
Processing of Ti-64 by Laser Powder Fed Additive Manufacturing
Nicholas Gosse, Dalhousie University
253 USA
Additive Manufacturing in CubeSats
Kuba (Jakub) Preis, California Polytechnic State University, San Luis Obispo
255 USA
SuperPowder: Quantitative Morphological Analysis of Metal Powders with Computer Vision
Andrew R. Kitahara, Carnegie Mellon University
256 USA
Residual Stress Development in Additively Manufactured Nickel Superalloys as a Function of Part Spatial Location and Orientation
Caleb E. Andrews, Drexel University
257 USA
3D Printing of Biomimetic Inspired Zircon Ceramic Structures
Tejesh Dube, Indiana University—Purdue University Indianapolis
258 USA
Optimizing Extrusion Process Using Water Atomized 17-4 PH Stainless Steel Powders
Jian Zhang, Indiana University—Purdue University Indianapolis
262 USA
Process Monitoring and Control Using Electron Signals in the EBM Process
Mouda Tung, North Carolina State University
265 USA
Simulations of the Stress Field Around a Sinter-Crack
Joseph R. Carazzone, Rice University
266 USA
Powder Consolidation Followed by High Pressure Torsion to Enhance the Strength of Novel Silver Alloys
Evander H. Ramos, University of California, Riverside
267 USA
Bottom-Up Approaches for Production of High Strength Ultrafine Grained Silver Alloys
Erik W. Sease, University of California, Riverside
270 USA
Effect of Solids Loading, Volumetric Flow Rate, and Layer Height on the Properties of Metal Fused Filament Fabrication of Bronze
Mohammad Qasim Shaikh, University of Louisville
272 USA
Additive Manufacturing of ODS FeCrAl via In Situ Oxidation
Ty Austin, University of Tennessee, Knoxville
273 USA
Chemistry in Binder Jet Additive Manufacturing
Dustin B. Gilmer, University of Tennessee, Knoxville
274 USA
Setter Strategies for Reduce Sintering Distortion of Binder Jetted Parts
Christopher S. Shafer, University of Tennessee,
Knoxville
275 USA
Ultra-fine Microstructure Formation During Hydrogen Sintering Phase Transformation
Munro J. Alley, University of Utah
277 USA
Alternating-Material-Deposition Additive Manufacturing for Site-Specific Property Control in Engineering Structures
Kellen D. Traxel, Washington State
University
278 USA
Direct Fabrication of Ti6Al4V+ Al12Si Compositionally Graded Materials by Laser Engineered Net Shaping
Yanning Zhang, Washington State University